Subject: Re: [harryproa] How wide are monohull slips?
From: George Kuck
Date: 11/20/2008, 8:04 PM
To: harryproa@yahoogroups.com.au
Reply-to:
harryproa@yahoogroups.com.au

Hello Gardner,
 
You will find moorings at Worton Cr marina or Green point marina on eastern side of Chesapeake bay, directly east of Pools Is. and Aberdeen Proving ground.
 
You can also rent a slip from Chesapeake Landing which has two docks, one on Worton Cr and one on Mill Cr.   I use Mill Cr. for $100. per year.  The dock is mostly empty except for my boat and many pilings missing so wide boat OK. The Worton Cr. dock wound not have wide slip. You will need to buy a lot or house to be able to join community association.  You will also have to time departure with tide as there is only 2' to 2 1/2' at high tide and less than 1' at low, but you can't beat the price.
 
 
I beleive there are some marinas that cater to multihulls in Georgetown, MD on Sassafras river that may be closer to you if comming around north end of bay.
 
Good luck with your projects,
 
George Kuck
Chestertown, MD    
 
        

--- On Thu, 11/20/08, Gardner Pomper <gardner@networknow.org> wrote:
From: Gardner Pomper <gardner@networknow.org>
Subject: Re: [harryproa] How wide are monohull slips?
To: harryproa@yahoogroups.com.au
Date: Thursday, November 20, 2008, 6:03 PM

Hi,

I have been sending emails to marinas in the Annapolis, MD area and also visiting a few slightly north of there. The responses so far indicate that most all 50' monohull slips will accommodate a 16' beam. After that it starts to get less common. I have found a few that will accept a boat up to a 19' beam. Finding a slip for a beam beyond 20' is really, really hard in the Chesapeake. Generally, I have been told, you need to find a marina with 2 monohull slips and pay to get the diving pilings removed, and pay again to get them put back and then pay for 2 slips. There are very, very few mooring fields available, and most all the T-docks are already taken up with the growing number of cats in the area.

Travel lifts are also a restriction. I have found that the older marinas tend to have ones only 17' wide, but there are a couple around that can haul a boat with a 24' beam (max).

This is reinforcing the idea I have been playing with, to make a liveaboard harry with a 24' beam (was 26, but I just reduced it <grin>) that will collapse to 16' to store in a marina. That would be another huge advantage for the harry design over the existing catamarans in the Chesapeake, anyway.

Thanks for all the feedback. I will keep trying to expand my sample of marina to see if the same holds true in other places along the east coast of the US.

- Gardner Paper
York, PA

On Wed, Nov 19, 2008 at 8:18 PM, Paul Wilson <opusnz@yahoo. ca> wrote:
In some countries you pay by the berth length, not the boat length.  In New Zealand, for example, many marinas will have 10, 12, 14 or 16 meter berths.  If your boat was (for example) 14.5 meters (45.9 feet) you will be charged for a 16 meter berth.  A good argument to keep a boat less than 14 meters.
 
Bellingham Marine seem to be building a lot of marinas all over the world.  You might want to contact them and see what their standard sizes are…..
 
 
Cheers, Paul
From: harryproa@yahoogrou ps.com.au [mailto:harryproa@yahoogrou ps.com.au] On Behalf Of carlos Solanilla
Sent: Thursday, November 20, 2008 11:43 AM Subject: Re: [harryproa] How wide are monohull slips?
 
Gardner
I think width is something you can always work with the marina - you can be at the end slip for example.
 
Be careful that most marina will take their yard tape and measure your boat to the nearest feet and charge you accordingly
 
A 50 ft long lw hull will cost you a lot for a slip in most places but on a mooring field is a different story so it might be a good idea to build a good dinghy (make it a catamaran) and plan to go back and forth - will be a lot cheaper at the end
 
my 2 cents
 

From: Gardner Paper <gardner@networknow. org>
To: harryproa@yahoogrou ps.com.au
Sent: Wednesday, November 19, 2008 3:20:56 AM
Subject: [harryproa] How wide are monohull slips?
Hi,
 
I continue to play around with my ideas for a 50' liveaboard, ocean crossing harryproa. I have a layout where it may be feasible to collapse the boat to a 16' beam. I realize that I don't actually know if that helps. Is anyone familiar enough with monohull slip dimensions to know if a reasonable percentage of 50' long slips can accommodate a 16' beam? 
 
I am primarily interested in marinas along the east coast of the US, but would also like to know elsewhere in the world.
 
For those in the world with a rational measurement system, I believe I am talking about 15m length and 5m beam (roughly).
 
With my design, it is not something you would do for a transient slip, but if you need to leave the boat for a month, or liveaboard in a marina, it might be helpful.
 
Thanks,
- Gardner
York, PA
 
 
No virus found in this incoming message.
Checked by AVG - http://www.avg. com
Version: 8.0.175 / Virus Database: 270.9.8/1800 - Release Date: 11/19/2008 6:55 PM


__._,_.___
Recent Activity
Visit Your Group
Y!7 Toolbar

Get it Free!

easy 1-click access

to your groups.

Yahoo!7 Groups

Start a group

in 3 easy steps.

Connect with others.

.

__,_._,___